PARK ASSIST / MONITORING PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) Reverse Signal Circuit
DESCRIPTION
The navigation receiver assembly*1 or radio and display receiver assembly*2 receives a reverse signal from the park/neutral position switch assembly*3 or back-up light switch assembly*4.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
*3: except Manual Transaxle
*4: for Manual Transaxle
WIRING DIAGRAM
 Reverse Signal Circuit_files/E271194E04.png "E271194E04")
 Reverse Signal Circuit_files/E271194E03.png "E271194E03")
CAUTION / NOTICE / HINT
- NOTICE:
-
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
 Reverse Signal Circuit_files/E270655.png "E270655")
Enter the "Function Check/Setting I" mode and select "Vehicle Signal".
Check that the display changes between ON and OFF according to the shift lever position.
- OK:
Shift Lever Position Display R ON Except R OFF
- HINT:
-
This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
- Result:
Proceed to OK NG (for Navigation Receiver Type, except Manual Transaxle) NG (for Navigation Receiver Type, for Manual Transaxle) NG (for Radio and Display Type, except Manual Transaxle) NG (for Radio and Display Type, for Manual Transaxle)
OK
NG (for Navigation Receiver Type, except Manual Transaxle)
NG (for Navigation Receiver Type, for Manual Transaxle)
NG (for Radio and Display Type, except Manual Transaxle)
NG (for Radio and Display Type, for Manual Transaxle)
Remove the park/neutral position switch assembly.
for U760E:
for U660F:
for K111:
Inspect the park/neutral position switch assembly.
for U760E:
for U660F:
for K111:
- Result:
Proceed to OK NG
OK
NG
for U660F
for U760E
for K111
Disconnect the B36 park/neutral position switch assembly connector.
Disconnect the G139 navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection Switch Condition Specified Condition B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition B36-2 (RL) - G139-2 (REV) Always Below 1 Ω B36-2 (RL) - Body ground Always 10 kΩ or higher
- Result:
Proceed to OK NG
OK
NG
Remove the back-up light switch assembly.
for EA64F:
for EB61F:
Inspect the back-up light switch assembly.
for EA64F:
for EB61F:
- Result:
Proceed to OK NG
OK
NG
for EA64F
for EB61F
Disconnect the B35 back-up light switch assembly connector.
Disconnect the G139 navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection Switch Condition Specified Condition B35-2 - Body ground Ignition switch ON 11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition B35-1 - G139-2 (REV) Always Below 1 Ω B35-1 - Body ground Always 10 kΩ or higher
- Result:
Proceed to OK NG
OK
NG
Remove the park/neutral position switch assembly.
for U760E:
for U760F:
for U660F:
for K111:
for K111F:
Inspect the park/neutral position switch assembly.
for U760E:
for U760F:
for U660F:
for K111:
for K111F:
- Result:
Proceed to OK NG
OK
NG
for U760E:
for U760F:
for U660F:
for K111:
for K111F:
Disconnect the B36 park/neutral position switch assembly connector.
Disconnect the G143 radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection Switch Condition Specified Condition B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition B36-2 (RL) - G143-2 (REV) Always Below 1 Ω B36-2 (RL) - Body ground Always 10 kΩ or higher
- Result:
Proceed to OK NG
OK
NG
Remove the back-up light switch assembly.
for EA64:
for EA64F:
for EB61:
for EB61F:
for EB63F:
Inspect the back-up light switch assembly.
for EA64:
for EA64F:
for EB61:
for EB61F:
for EB63F:
- Result:
Proceed to OK NG
OK
NG
for EA64:
for EA64F:
for EA61:
for EA61F:
for EA63F:
Disconnect the B35 back-up light switch assembly connector.
Disconnect the G143 radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection Switch Condition Specified Condition B35-2 - Body ground Ignition switch ON 11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition B35-1 - G143-2 (REV) Always Below 1 Ω B35-1 - Body ground Always 10 kΩ or higher
- Result:
Proceed to OK NG
OK
NG
 Reverse Signal Circuit_files/fbx_x.png "close")